How Should You Pick a 4-Slot M.2 Adapter Card? Three Cards Tested, PCIe 5.0 Reaches 14,000 MB/s
Share
The LEKUO PD42M43 (formerly IO-PCE44M2-02), PX24M41 and PB65MX4 are all four-slot M.2 NVMe adapter cards, and all three are driver-free. Some people use them as 4-bay NVMe expansion, some as M.2 NVMe array cards, others simply as SSD expansion — yet drop them into the same machine and the results are completely different: the fastest single drive reaches 14 GB/s, the slowest only 1.7 GB/s; some work the moment you plug them in, others need a detour through the BIOS first.Only two things differ: how many lanes the upstream link gets, and whether the card carries a switch chip.
Upstream Interface
The three cards run PCIe 5.0 x16, PCIe 4.0 x8 and PCIe 4.0 x4 respectively — what matters is how much headroom is left over to feed the next drive once one of them cannot saturate the link.
A Switch Chip Decides Whether You Touch the BIOS
Direct-attach: the four M.2 slots hang straight off the upstream lanes, with no chip on the card (PD42M43).Switched: the four M.2 slots sit behind a chip, and the upstream link occupies only one (PX24M41 uses an IX8024, PB65MX4 uses the B650 SouthBridge).
PCIe bifurcation splits one x16 link into several x4 links for different devices. Consumer motherboards either support it only on particular slots, or require you to select x4x4x4x4 manually in the BIOS; pre-built systems often lock the option out altogether.
PD42M43 is a direct-attach card, so the four independent x4 links have to be supplied by the motherboard — otherwise the drives are not all detected, or not at full speed. The MSI Z890 used for testing only came up after it was set to x8x4x4. The other two carry a switch chip on the card itself — an IX8024 on the PX24M41, the B650 SouthBridge on LEKUO's own SouthBridge Extended platform for the PB65MX4 — so the motherboard only ever sees "one card occupying one link". That is where no motherboard bifurcation required comes from, and why older boards and pre-built systems can both take them.
Single-Drive Speed
PD42M43 with a Samsung 9100 PRO 1TB, link negotiated at PCIe 5.0 x4 / 32.0 GT/s (all figures in MB/s):
Sequential read 14.1 GB/s and write 13.0 GB/s — essentially saturating PCIe 5.0 x4.
PX24M41 single-drive sequential: three 980 PRO plus one 990 PRO (CDM 8.0 / 1 GiB):
6.7–7.1 GB/s per drive, with all four slots consistent — none of them is short-changed.
PB65MX4 has four slots of differing specification, so they have to be read separately:
Across the three: the peak single-drive figure on the PB65MX4 rear (7086) is on par with the PX24M41 (7142), while the PD42M43 leads both by a factor of two. But put a drive in the PB65MX4 front slots and it drops to 1766 MB/s — the single easiest thing to overlook when buying.
Multi-Drive Concurrency
PX24M41's IX8024 gives each of the four drives its own lanes:
16.4 GB/s is exactly the theoretical ceiling of PCIe 4.0 x8 — the upstream link is saturated and the switch adds no penalty. That is the point of a PCIe Switch architecture: not to make a single drive faster, but to keep four drives from fighting each other when they run together. Multi-drive software RAID 0 / RAID 10 array nodes, drive-to-drive batch copy workstations and full-system data migration need precisely this.
PB65MX4 has only x4, so four ports running together have to contend:
The narrower the link, the harder concurrency falls. The specification states it plainly: "All ports share the PCIe 4.0 x4 upstream bandwidth, so the four slots cannot run at full speed simultaneously." It suits scenarios where each drive does its own job, not high-concurrency arrays.
PD42M43 with three drives running concurrently (CrystalDiskMark 9.0.3 / 1 GiB; only three drives were tested in this run):
With three drives running together, the PCIe 5.0 drive still holds 13252 MB/s, and the 26.6 GB/s total takes only about four tenths of the 512 Gbps (64 GB/s) upstream — most of the headroom is still untouched, and each drive runs at close to its own speed.
What Else Can It Drive
The PB65MX4 is the only one that reaches outward: it adds 20 Gbps USB-C, 10 Gbps Type-E and 6-pin auxiliary power. What a build usually lacks is not drive bays but the Type-C header sitting unused on the front panel.
Cooling and Operating Systems
What Each Card Does Best
Which One Should You Choose
All three are PCIe storage expansion cards, but their fit does not overlap.
Video editing media drives, AIGC models and asset libraries, 3D rendering and audio production → PD42M43. The 14 GB/s single-drive speed is something neither of the other two can offer; in multi-track 4K/8K playback, large model weight I/O and render caches, the gap shows up directly as waiting time. The precondition is a motherboard that supports PCIe 5.0 bifurcation and a free x16 slot.
Workstation expansion, small studio servers, NAS storage expansion, multi-drive software RAID 0 / RAID 10, local AI inference and deep-learning nodes → PX24M41. Four drives reading and writing at once without contention is exactly what array nodes, batch copy and high-performance computing need; no motherboard bifurcation plus cross-platform support means you need not shop for a particular board.
Older motherboard upgrades, pre-built systems, SSD expansion, and adding a front-panel Type-C along the way → PB65MX4. One x4 slot is all it takes, and the upgrade brings 20G USB-C and a front-panel header with it. Suited to scenarios where each drive does its own job, not to high-concurrency arrays.
Gaming PC upgrades → all three work. For one or two game drives the PB65MX4 has the lowest barrier; for the fastest possible load times the PD42M43 is the better fit.
🛒:https://lekuo.shop/products/lekuo-southbridge-extend
🛒:https://lekuo.shop/products/lekuo-sohttps://lekuo.shop/products/pcie4-4x-m2-nvme-adapter-px24m41?_pos=1&_sid=b80bd4e5a&_ss=r