Budget PCIe 5.0 x16 to 4-Slot M.2 NVMe Expansion Card, Measured at 14,000 MB/s
Share
One free x16 slot left on the motherboard, and three or four M.2 SSDs already sitting in a drawer — a situation most builders run into late in a build.A four-slot M.2 adapter card turns that one slot into four positions: four PCIe 5.0 x4 links on independent lanes, each drive getting on with its own job.This article looks at the more cost-effective way to do it at the budget end of the market: a measured 14151 MB/s sequential read on a single drive.
First, What It Is: PCIe 5.0 x16
PD42M43 is a PCIe to M.2 expansion card from LEKUO, and it does one very direct thing: it splits a motherboard's PCIe 5.0 x16 link into four M.2 M-Key slots, each running PCIe 5.0 x4.
There is no switch chip on the card, and no firmware to load. It does not manage bandwidth allocation — it only divides the 16 lanes physically into four groups of four, each routed to one slot.
How the Four Slots Are Wired: Each Drive Gets Its Own x4
The whole card is a one-to-four direct-attach layout: 16 lanes arrive at the gold fingers, the board divides them evenly into four groups, and each group feeds one M.2 slot on its own independent x4. There is no sharing and no arbitration between the four slots — each drive sees only its own x4, and how fast it runs depends on the drive itself.
The design brings two direct benefits. First, single drives do not contend: a Gen5 drive plugged in runs at full PCIe 5.0 x4 speed and is not slowed down by the others. Second, when several drives run in parallel each has its own lanes, so all four can run at once.
On compatibility, watch length and mounting. All four positions support 2230 through 2280, and each position has screw holes at all four lengths — 2230 / 2242 / 2260 / 2280 — so a short drive is never left unsupported. Enterprise drives such as 22110 will not fit.
Power is straightforward: up to 14 W per drive, so drives rarely drop out for lack of power. Do not expect it to feed four drives at full draw at the same time, though — the whole card still draws from that single x16 slot.
Tested: The Conditions Behind 14,000 MB/s
The figures below come from one complete test run, on a configuration that is mainstream consumer kit today:
Single-drive results (MB/s):
Three drives running at the same time:
Two things in this data are worth pointing out. First the drop: drive F falls from 14151 on its own to 13252, a loss of only about 6% — with three drives loaded at once the Gen5 drive is barely affected, which shows the four x4 links really are independent. Then the headroom: 26.6 GB/s across three drives takes only about four tenths of the 64 GB/s x16 upstream, so there is still room for a fourth drive.
That decides what it suits: media drives reading and writing at once, several VM images in parallel, whole-machine copies — anything where multiple drives move together, it holds up. But if you intend to run four Gen5 drives at full sequential read simultaneously, you will theoretically reach the 64 GB/s upstream ceiling — that workload belongs on a switch-based design with a wider upstream.
Where Does the Value Come From?
What that tenfold price buys is really just one thing: the switch chip manages the lanes for you, and along the way keeps you out of the BIOS. If your motherboard supports bifurcation, that money is better spent on drives.
Specifically, the saving comes in three places:
- No switch chip. One fewer controller plus its companion firmware on the BOM — the main source of the price gap.
- No driver. Plug it in and you get four standard NVMe devices; Windows and Linux pick them up directly.
- No extra power cable. It draws from the x16 slot, so there is no 6-pin to route through the case — one less step at build time.
Who Should Buy It, and Four Things to Confirm First
It suits: anyone who already has one or two Gen5 SSDs and needs more drives but has run out of slots, on a motherboard that supports bifurcation; video editing media drives, 3D render caches and audio project drives that need fast single-drive speed plus simultaneous reads; model and asset libraries and frequent whole-machine copies; and budget-conscious builders willing to spend ten minutes enabling bifurcation in the BIOS.
Less suited: Mac users (the specification lists Windows / Linux only); anyone whose motherboard does not support bifurcation and who does not want to change platform — a switch-based version is simpler in that case; and high-concurrency arrays that need four Gen5 drives at full sequential read, which call for a wider upstream.